PilotOdyssey.com
http://pilotodyssey.com/PO/

FL Superlite Racing Engine
http://pilotodyssey.com/PO/viewtopic.php?f=124&t=20659		 Page 1 of 1
Author:  Rppjr [ Mon Dec 28, 2020 1:41 pm ]
Post subject:  FL Superlite Racing Engine
Here are some more pictures of the Engine in the other thread.

Attachments:
IMG_7349.JPG
IMG_7349.JPG [ 47.15 KiB | Viewed 1608 times ]
IMG_7350.JPG
IMG_7350.JPG [ 67.34 KiB | Viewed 1608 times ]
IMG_7351.JPG
IMG_7351.JPG [ 49.01 KiB | Viewed 1608 times ]
IMG_7353.JPG
IMG_7353.JPG [ 48.55 KiB | Viewed 1608 times ]
IMG_7355.JPG
IMG_7355.JPG [ 50.28 KiB | Viewed 1608 times ]
IMG_7358.JPG
IMG_7358.JPG [ 57.66 KiB | Viewed 1608 times ]
Author:  Rppjr [ Mon Dec 28, 2020 1:47 pm ]
Post subject:  Re: FL Superlite Racing Engine
and more

Attachments:
IMG_7363.JPG
IMG_7363.JPG [ 46.38 KiB | Viewed 1607 times ]
IMG_7364.JPG
IMG_7364.JPG [ 38.71 KiB | Viewed 1607 times ]
IMG_7366.JPG
IMG_7366.JPG [ 48.96 KiB | Viewed 1607 times ]
IMG_7367.JPG
IMG_7367.JPG [ 42.78 KiB | Viewed 1607 times ]
IMG_7369.JPG
IMG_7369.JPG [ 47.7 KiB | Viewed 1607 times ]
IMG_7372.JPG
IMG_7372.JPG [ 53.19 KiB | Viewed 1607 times ]
Author:  Rppjr [ Mon Dec 28, 2020 1:52 pm ]
Post subject:  Re: FL Superlite Racing Engine
and some more...

Attachments:
IMG_7373.JPG
IMG_7373.JPG [ 60.43 KiB | Viewed 1607 times ]
IMG_7374.JPG
IMG_7374.JPG [ 56.11 KiB | Viewed 1607 times ]
IMG_7375.JPG
IMG_7375.JPG [ 48.18 KiB | Viewed 1607 times ]
IMG_7377.JPG
IMG_7377.JPG [ 65.21 KiB | Viewed 1607 times ]
IMG_7379.JPG
IMG_7379.JPG [ 31.02 KiB | Viewed 1607 times ]
IMG_7380.JPG
IMG_7380.JPG [ 27.13 KiB | Viewed 1607 times ]
Author:  canadian oddy [ Mon Dec 28, 2020 2:57 pm ]
Post subject:  Re: FL Superlite Racing Engine
I like that custom counter balancer cover.

CO
Author:  fully [ Wed Dec 30, 2020 7:23 pm ]
Post subject:  Re: FL Superlite Racing Engine
I didn't know they used a Yamaha rod..maybe that's why you need that thicker spacer plate.
Author:  hoser [ Fri Dec 08, 2023 11:29 pm ]
Post subject:  Re: FL Superlite Racing Engine
fully wrote:
I didn't know they used a Yamaha rod..maybe that's why you need that thicker spacer plate.


Yeah probably a long rod Engine, I have seen 350 engines built like that before, weld on a Kawasaki reed cage flange, runs a Kawasaki reed cage, weld on a new exhaust flange, change the exhaust port to a large non bridged design.

Cylinder skirt looks scary thin.

Notice the relief cuts in the crankcases to allow clearance for the piston skirts on each side. Check that clearance when installing a new piston.

See if you can find numbers on the rod and document

Document the numbers on the piston. If you split the cases try to get a pin diameter on the big end of the rod and or inspect to see if its been machined out larger. See if the crank cases been clearanced for the rod.

I think I have a set of old stock cases and a crank I can measure from if you need to verify crank pin diameter or need to compare for case modifications.
Author:  Rppjr [ Sun Feb 04, 2024 9:11 pm ]
Post subject:  Re: FL Superlite Racing Engine
I sent this Engine to Methodical to go through for me. I can update once I get more info.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/