PilotOdyssey.com
http://pilotodyssey.com/PO/

FL350 Restore x 3
http://pilotodyssey.com/PO/viewtopic.php?f=5&t=20769		 Page 1 of 2
Author:  GarlicGreg [ Tue Jul 06, 2021 2:08 pm ]
Post subject:  FL350 Restore x 3
Here is the start of my project. Picked up the first batch of parts from the powder coater. My plan is to set up an assembly line and document my progress over all and with sub-assemblies. This pic was from awhile ago. I'm going to catch up with my posts.

Attachments:
IMG_20200908_215532_645.jpg
IMG_20200908_215532_645.jpg [ 58.08 KiB | Viewed 21375 times ]
Author:  GarlicGreg [ Tue Jul 06, 2021 4:58 pm ]
Post subject:  Re: FL350 Restore x 3
Here is a sampling of some of my my NOS parts stash a foot tub a fender and steering column side cover pulled from storage.

Attachments:
20210308_171643.jpg
20210308_171643.jpg [ 47.68 KiB | Viewed 21357 times ]
Author:  GarlicGreg [ Tue Jul 06, 2021 5:02 pm ]
Post subject:  Re: FL350 Restore x 3
I was able to source new ball joint boot rubber from a Honda JDM car. It is the same part number as the NLA Odyssey ones. I got them from the UK.

Attachments:
20210308_173347.jpg
20210308_173347.jpg [ 56.09 KiB | Viewed 21356 times ]
Author:  GarlicGreg [ Tue Jul 06, 2021 5:07 pm ]
Post subject:  Re: FL350 Restore x 3
NLA front bumper rubbers.

Attachments:
20210318_194418.jpg
20210318_194418.jpg [ 43.36 KiB | Viewed 21355 times ]
20210318_194456.jpg
20210318_194456.jpg [ 45.37 KiB | Viewed 21355 times ]
Author:  GarlicGreg [ Tue Jul 06, 2021 5:12 pm ]
Post subject:  Re: FL350 Restore x 3
Front bumper repair. Before and after.

Attachments:
20210407_173949.jpg
20210407_173949.jpg [ 171.25 KiB | Viewed 21355 times ]
20210407_173816.jpg
20210407_173816.jpg [ 129.21 KiB | Viewed 21355 times ]
20210407_173851.jpg
20210407_173851.jpg [ 118.97 KiB | Viewed 21355 times ]
Author:  GarlicGreg [ Wed Jul 07, 2021 3:34 pm ]
Post subject:  Re: FL350 Restore x 3
I stripped down my air guides, reconditioned the rubber, powder coated the metal and re-riveted them back together.

Attachments:
20210603_173350.jpg
20210603_173350.jpg [ 48.65 KiB | Viewed 21324 times ]
Author:  Kuma [ Wed Jul 07, 2021 3:58 pm ]
Post subject:  Re: FL350 Restore x 3
looking good, don't make it so nice you won't want to go out and enjoy it!
Author:  GarlicGreg [ Wed Jul 07, 2021 4:25 pm ]
Post subject:  Re: FL350 Restore x 3
Kuma wrote:
looking good, don't make it so nice you won't want to go out and enjoy it!

I'm building this one to sell. I have 6 others to ride!
Author:  GarlicGreg [ Thu Jul 08, 2021 1:45 am ]
Post subject:  Re: FL350 Restore x 3
NOS axels

Attachments:
20210403_135828.jpg
20210403_135828.jpg [ 51.03 KiB | Viewed 21299 times ]
Author:  GarlicGreg [ Thu Jul 08, 2021 1:51 am ]
Post subject:  Re: FL350 Restore x 3
Recoveted seat with red stitching.

Attachments:
20210313_162522.jpg
20210313_162522.jpg [ 72.07 KiB | Viewed 21297 times ]
Author:  GarlicGreg [ Fri Jul 09, 2021 12:07 am ]
Post subject:  Re: FL350 Restore x 3
Assembly line.

Attachments:
20210708_184004.jpg
20210708_184004.jpg [ 78.67 KiB | Viewed 21274 times ]
Author:  GarlicGreg [ Sat Jul 10, 2021 1:32 pm ]
Post subject:  Re: FL350 Restore x 3
Refreshed transmission with new seals and bearings.

Attachments:
20210401_161045.jpg
20210401_161045.jpg [ 80.74 KiB | Viewed 21237 times ]
Author:  GarlicGreg [ Sat Jul 10, 2021 1:36 pm ]
Post subject:  Re: FL350 Restore x 3
Cables and wiring hung, ready to place transmission.

Attachments:
20210308_174300.jpg
20210308_174300.jpg [ 103.37 KiB | Viewed 21236 times ]
Author:  GarlicGreg [ Sat Jul 10, 2021 1:40 pm ]
Post subject:  Re: FL350 Restore x 3
New bearings and seal for axel carriers.

Attachments:
20210530_131232.jpg
20210530_131232.jpg [ 56.84 KiB | Viewed 21236 times ]
Author:  canadian oddy [ Sat Jul 10, 2021 2:02 pm ]
Post subject:  Re: FL350 Restore x 3
Very Very Nice
You're gona give CurtisR401 a run for his money.
It's gona be a toss up for first place but I think you got it.
Since you got all NOS stuff that thing should be in a show room.
Contact Honda.
I bet they pay the most.
CO
Author:  GarlicGreg [ Sat Jul 10, 2021 3:49 pm ]
Post subject:  Re: FL350 Restore x 3
Thanks. I might just put it one of them on a pedestal in my man cave. Definitely will be too nice to drive.
Author:  GarlicGreg [ Sat Jul 10, 2021 3:53 pm ]
Post subject:  Re: FL350 Restore x 3
Measured brake disc. Plenty of meat left on it. Cleaned it up an Ceracoated the inner part.

Attachments:
20210704_132401.jpg
20210704_132401.jpg [ 35.87 KiB | Viewed 21229 times ]
20210605_183147.jpg
20210605_183147.jpg [ 57.96 KiB | Viewed 21229 times ]
20210605_183413.jpg
20210605_183413.jpg [ 74.51 KiB | Viewed 21229 times ]
20210605_185345.jpg
20210605_185345.jpg [ 85.35 KiB | Viewed 21229 times ]
Author:  canadian oddy [ Sat Jul 10, 2021 6:33 pm ]
Post subject:  Re: FL350 Restore x 3
Use some light thread locker (blue) on that big disk nut.
I have had them come lose.
CO
Author:  GarlicGreg [ Sat Jul 10, 2021 6:50 pm ]
Post subject:  Re: FL350 Restore x 3
Yup good call! I've got the manual and it indicates that and torque spec. I had to source a 36mm wrench that would allow me to get the torque wrench at 90⁰ to properly seat it. Also manual says to use motor (( Internal Combustion Engine ? )) oil on the lock nuts that hold the brake disc on. I'm following manual religiously on wear specs, torque, lube and threadlocker application.

Attachments:
20210710_154742.jpg
20210710_154742.jpg [ 56.55 KiB | Viewed 21216 times ]
Author:  GarlicGreg [ Sun Jul 11, 2021 2:18 am ]
Post subject:  Re: FL350 Restore x 3
Tested then polished the shock bodies, powder coated the springs and installed new bump stops. The only thing that bothers me is the plastic spacers between shock bodies and springs are a little rough in a couple spots, not perfect but I can't find any perfect ones.

Attachments:
20210606_194419.jpg
20210606_194419.jpg [ 53.16 KiB | Viewed 21202 times ]
20210626_201416.jpg
20210626_201416.jpg [ 39.6 KiB | Viewed 21202 times ]
20210627_122501.jpg
20210627_122501.jpg [ 62.07 KiB | Viewed 21202 times ]
20210627_122527.jpg
20210627_122527.jpg [ 51.99 KiB | Viewed 21202 times ]
Author:  GarlicGreg [ Sun Jul 11, 2021 2:21 am ]
Post subject:  Re: FL350 Restore x 3
Brake backing plates got powder coated. All new brake hardware.

Attachments:
20210702_105549.jpg
20210702_105549.jpg [ 58.78 KiB | Viewed 21202 times ]
20210702_111049.jpg
20210702_111049.jpg [ 53.43 KiB | Viewed 21202 times ]
Author:  GarlicGreg [ Sun Jul 11, 2021 2:24 am ]
Post subject:  Re: FL350 Restore x 3
New rubber on the fuel tank skid plate.

Attachments:
20210603_173635.jpg
20210603_173635.jpg [ 64.81 KiB | Viewed 21201 times ]
Author:  GarlicGreg [ Sun Jul 11, 2021 5:01 pm ]
Post subject:  Re: FL350 Restore x 3
Test fitting parts. It's like you build it 3 times by the time you're done. Assemble, discover an issue, take apart, fix, test fit, disassemble then reassemble with proper fasteners, lube, locktite and torque.

Attachments:
20210410_133640.jpg
20210410_133640.jpg [ 87.77 KiB | Viewed 21181 times ]
Author:  CurtisR401 [ Mon Jul 12, 2021 1:42 pm ]
Post subject:  Re: FL350 Restore x 3
canadian oddy wrote:
Very Very Nice
You're gona give CurtisR401 a run for his money.
It's gona be a toss up for first place but I think you got it.
CO


LOL :-)

I would have to agree, you got me beat! Great work and they are sure to be beautiful machines when completed. Keep up the good work I am looking forward to seeing them completed.

Cheers, Curtis
Author:  fully [ Fri Jul 16, 2021 12:12 pm ]
Post subject:  Re: FL350 Restore x 3
im all for restoring, but I hate garage queens..they look nice but man you got to drive them..
Page 1 of 2 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/